VITURE glasses won't turn on? Press any button first
VITURE glasses have no battery or power switch. If yours stay dark, the screen may be off, asleep or on a port without video. Fixes for the Beast, Luma and Pro 2.
VITURE glasses don't have a battery or a power switch. VITURE's own setup steps are short: turn on and unlock your device, and "the XR Glasses will power on automatically." So if yours stay dark, something between the device and the glasses is off. Often it's a button press you didn't mean to make. Start at the top.
Note
We built this page from VITURE's manuals for the Beast, Luma series, Pro 2, Pro XR and One, plus its Mobile Dock Mini and Pro Neckband guides, checked November 17, 2026. We haven't reproduced every case on our own glasses yet.
1. Press any button: the screen may just be off
Most VITURE glasses have a press that turns the screen off. It's easy to hit by accident while you change the brightness. The good news: VITURE says any button wakes it.
| Glasses | Turns the screen off | To wake |
|---|---|---|
| Beast | Hold L- | Press any button |
| Luma, Luma Pro, Luma Ultra | Hold L1 | Press any button |
| Pro XR and One | Hold the - button | Press any button |
| Pro 2 | None listed | Not needed |
On the Beast, holding L- turns off the tint film too, not just the screen.
2. Unlock your device
VITURE's steps start with "turn on and unlock your device." Wake your phone, laptop or Steam Deck and get past the lock screen. Then give the glasses a few seconds.
3. Put them on: Wearer Detection may have them asleep
VITURE glasses can tell when you take them off. With Wearer Detection on, the screen turns off about a minute after you take them off. Put them back on and the picture should return. So glasses sitting on a desk can look dead.
- Switch it off on VITURE's update page, viture.com/firmware/update, if you'd rather it stayed on.
- Pro 2 owners: firmware 0.00.003 from November 12, 2026 fixed Wear Detection turning the screen on or off by mistake. Update if the screen keeps blinking off while you wear them.
- Beast owners: the menu has an Auto Shutdown setting too. VITURE says it "automatically turns off the display after inactivity."
4. Unplug other screens and try another port
This is VITURE's own fix for a blank screen. Disconnect any other external displays from your device, because "some device models support only one external display." Then try a different USB-C port.
Laptops with a monitor already plugged in are the usual case. On a Mac, our VITURE Mac fix covers the rest.
5. Make sure the port sends video
Your device's USB-C port has to send video. VITURE says to look for "DisplayPort over USB-C, DP Alt Mode, Alt DP over USB-C, or Thunderbolt 4" in its specs. Here's how to check yours.
- iPhone 15 and later work directly, except the iPhone 16e and iPhone Air, per VITURE's Pro 2 manual. The iPhone 17e can't send video either.
- Switch, Switch 2, PS5 and Xbox need a VITURE dock or adapter.
- Budget Android phones often skip video out.
6. Check the cable
VITURE ships two kinds of cable, so make sure you're using the right one, pushed in all the way.
- Beast, Pro 2 and the base Luma use a USB-C to USB-C cable.
- Luma Pro, Luma Ultra, Pro XR and One use a cable with a magnetic connector that clips onto the glasses. Check that it snaps fully into place.
A spare USB-C cable from a drawer may only charge. Those can't carry video, so the glasses stay dark.
Using a Mobile Dock Mini?
The Dock Mini has its own battery, so it can be the part that's off.
- Dock won't turn on. VITURE says to charge it with a USB Power Delivery charger and cable. If it doesn't start on its own, keep it charging and hold its button for 3 seconds. Still nothing? VITURE says to contact support for a replacement.
- Dock dies mid-game. It powers off by itself at 3% battery.
- Glasses dark on the dock. Check whether Solo Mode works. If it does, switch to Hug Mode and use your own full-featured USB-C cable. If that works, VITURE says the included cable is faulty and support will replace it.
- Switch in Solo Mode. Plug power into the Charge Port. VITURE says "the Switch requires external power to output video."
- Blinking lights. A fast blink on the first LED means overheat protection. All four blinking means bootloader mode: reconnect the dock and update its firmware again.
Picking a dock? Here's the Dock Mini and Pro Mobile Dock compared.
Using a Pro Neckband?
The Neckband has a battery and a Power button on its left side. Hold it until you feel a vibration. A short press only puts it to sleep or wakes it, and after 3 minutes of sleep it shuts down by default. A red light means it's down to 20% or less. It takes about 1.5 hours to charge.
Update the firmware
Some VITURE updates fixed a missing picture on specific devices. The Beast's May 2026 update fixed no picture on the Pixel 10. Luma Pro and Luma Ultra updates in October fixed it on the Xiaomi 18 Fold. Our VITURE firmware log shows how to update in Chrome on a Windows PC or Mac.
Still dark?
Contact VITURE support. Tell them your glasses model, your device, the cable and every step you tried. On the Beast, the firmware version is in the menu under About, then Device Information. Bought in the last year? Here's how VITURE's warranty claims work.
Where to next
- Beast dark on a Switch 2? Our Beast and Switch 2 fix covers the dock, power and firmware.
- Settings tangled up? Here's how to factory reset VITURE glasses.
- Picture but no sound? Try the VITURE no sound fix.
- On XREAL instead? See XREAL glasses won't turn on.